Did you know?

Blue: WiFi is connected, and the unit is ready for the next use. White: WiFi is turned off. Blinking Blue: WiFi is disconnected / reconnecting. Learn more. Blinking Yellow: Unit is in Onboarding Mode. Follow the prompts in the app and scan the QR code on the back of the unit as directed. Press the Connect button to exit Onboarding Mode.Our litter robot 3 recently started flashing sequentially blue > yellow > red. It still functions normally otherwise. This started almost immediately after we opened the base to replace the rusted antipinch electrodes. Prior to replacing them, the litter robot continuously rotated counterclockwise non-stop (now resolved following antipinch electrodes replacement). Per recommendations from the ...Step 10: Manual Cat Sensor Activation. Press on the Globe just above the entrance in a forward and downward direction—just press and release. The blue light should turn off and the red light should come on. You've activated the Cat Sensor to simulate your cat entering the Globe, then exiting. Allow the Wait Time (3, 7, or 15 minutes ...Once the update is complete, your Litter-Robot should be ready for use. Successful: If your unit returned home and displays a blue light bar, you've been successful. Unsuccessful: If you are still seeing a green light bar with partial red flashing after resetting at the Home position, there's likely an issue with your Litter-Robot. The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won’t leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your phone if you ... Blue light flashing, hit reset and then the yellow lights flashes very fast…did all the cleaning but nothing fixes it…how do I order the replacement piece I need, how do I know what I need? ... Description Litter-Robot 3 Open Air DFI Hardware (v2) Replacement DFI Hardware for your Litter-Robot 3 Compatible with Litter-Robot 3 only Note ...Preparation. If Litter-Robot 4 displays a blue light bar with a blinking blue light adjacent to the Connect button, this indicates that the unit is connecting to the app or has disconnected and is trying to reconnect but has not successfully reconnected.One of the lights will start flashing, indicating the current cycle delay setting. Use the Reset button to toggle to the next setting: Blue = 3 minutes; Yellow = 7 minutes; Red = 15 minutes ; Press and hold the Empty button to save the setting. The blue light will blink to confirm, then return to standby.Watch on. The Litter-Robot 3 is equipped with a cat sensor that detects when a cat enters and exits the globe. If the cat sensor has been continuously activated for 30 minutes or more, either by a cat that won't leave the globe or by too much weight in the unit, the timing light will flash red. You will also receive a notification on your ...If your unit has a blue light bar with partial yellow flashing or the unit will not cycle, this indicates that the scale has been triggered for more than 30 minutes. You will also receive a notification on your phone if you use the Whisker App. Place the unit on a firm, level surface. Avoid soft, uneven, or unstable flooring for accurate weight ...Preparation. If Litter-Robot 4 has a blue light bar with a yellow blinking light adjacent to the Connect button, this indicates that the unit is in Onboarding mode and waiting to be connected to the app.. You can now proceed with the onboarding process within the Whisker App to finalize connection.. When your Litter-Robot 4 has successfully completed onboarding, the blinking yellow light will ...blue light flashing - waste drawer empty. Litter-Robot 3. hello! my robot has had a flashing blue light for the past few days even though the waste drawer is empty. it will …If your Litter-Robot 3 is displaying a yellow light flashing slowly, this indicates a cycle has been interrupted either by the cat sensor or bonnet removal. Press the Reset button to resume the cycle. If your unit returned home and displays a …If your Litter-Robot 3 is displaying a flashing red light or you are receiving cat sensor fault errors via the Whisker app, please follow the steps in this video to resolve this issue.5. Blue Light Blinking. Regarding issues with your Litter-Robot 3, you may also see the blue light blinking. Before troubleshooting, it's advisable to: Unplug your power supply and then wait for 10 seconds. Plug the unit back in and allow it to complete its cleaning cycle. If the light is solid blue, everything has reverted to normal.Litter-Robot 3: All three lights flashing (Globe position fault) Litter-Robot 3: Blue Light Flashing (Drawer Full) Litter-Robot 3: Buttons and Lights Litter-Robot 3: Cat not detected ; Litter-Robot 3: Cat Sensor Troubleshooting The automatic night light, located in the upper bonnet, is there to help guide your cat to the litter box. A light sensor located above the Cycle button detects ambient light and turns the night light on and off automatically. Turn the night light function on and off by pressing and holding the Power button. To troubleshoot the blue blinking, let's start by power cycling your unit: 1.) Leave your unit powered ON with the blue blinking light engaged and unplug your power supply from the base. 2.) Wait 10 seconds, then plug the unit back in. 3.) Allow the unit to complete a start-up cycle.I've had my litter robot 3 only around 6 weeks the last couple of weeks its been problematic with either flashing blue lights or flashing yellow lights, usually following cleaning guidlines resolves the issue despite no debris or dirt around the sensors after a couple of goes. Today it has a flashing blue light which wont clear, I cannot ...While some cannot wait for the summer to end so they can light a fire, put on cozy socks, and drink hot chocolate; others are already missing the warm sun, beaches, BBQs, and flip-...One of the lights will start flashing, indicating the current cycle delay setting. Use the Reset button to toggle to the next setting: Blue = 3 minutes; Yellow = 7 minutes; Red = 15 minutes ; Press and hold the Empty button to save the setting. The blue light will blink to confirm, then return to standby.If your unit temporarily displays a white light blinking in the middle of the light bar, this simply indicates that the unit was receiving an Over-The-Air firmware update. No action needs to be taken at this time. This may take up to 30 minutes to complete. Once the update is complete, your Litter-Robot should be ready for use.Litter-Robot 3 is about the size of a nightstand, while Litter-Robot 4 has a footprint similar to that of a large traditional litter box—so there's no need to make additional space. See exact dimensions below: Height: 29.5" (74.9cm) Width: 24.25" (68.6cm) Depth: 27" (68.6cm) Height: 29.5" (74.9cm) Width: 22" (55.8cm) Depth: 27" (68.6cm ...View and Download whisker Litter robot 3 manual online. litter robot 3 pet care product pdf manual download. Sign In Upload. Download Table of Contents Contents. ... Blue Light Flashing: Waste Drawer is Full The Waste Drawer is approaching full (see page 21). Remove the waste, install a new liner, then press Reset to cancel the flashing light ...Now, let's run a test cycle. Short press the ReseLitter-Robot 4: Blue and white alternating light bar (Mot I went to the litter robot Support and filled the steps. By doing a hard reset (unplugging the back of the unit for ten seconds) it was resolved. 1. Reply. Share. Ever since I changed the last bag, my litter robot 3 has had its blue light blinking after every use. I can hit reset and it stops, until the next….Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1-877-250-7729 Submit a ticket. Discover troubleshooting tips for your Litter-Robot 4 in solid blue ready mode. Browse our support guide to ensure optimal use. r/litterrobot. •. BootleggerBill. Help! Rapidly flashing yellow cy Help & Support Domestic Robots. Catbot November 28, 2023, 2:57am 1. Litter robot 3 is 1.5 years old, in use by 3-4 cats. Purchased as reconditioned from Litter Robot on line. Worked flawlessly until now. Been goofy for about 2 weeks. Constantly sends over torque fault to app, but I rarely find it out of place. Emptying the Liter-Robot. Press the Empty buton to cycle the

When I turn on the Litter Robot 3 (non-connect), blue light is flashing, then I press Reset and fast yellow light is flashing. When I press Reset again, blue light is flashing and so on.. What I checked so far: - Anti Pinch Pins looks good and are touching each other. - DFI is clean and 4 IR LEDs are blinking once a second.Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. ... To confirm the DFI has failed when there is a flashing blue light, leave the LR as is powered on, pull the waste drawer out and use your phones camera to look at the Left side DFI board, you should see 4 steady flashing lights on your camera screen, (from ...Litter-Robot 3 Connect: Download the Whisker App. ... Empty the waste drawer when indicated by the app or the flashing blue light on the control panel. How often you empty the waste drawer depends on the number and size of your cats. For two average-sized cats, twice per week is typical. For a single cat, once per week is usually sufficient.Tldr: my robot has a blue flashing light and none of the buttons do anything, only on/off. I've tried the basics. I've had the litter robot for a few years, but can't remember if it's a 1 or 2 model. I've encountered an issue I can't fix. It started with the quick flashing yellow light (pinch detector issue).I had this problem - it connected when I first set it up but then it went offline and the wifi light was blinking blue incessantly. I powered on and off, tried resetting, even uninstalled and reinstalled the app, nothing worked. Finally I deleted the device from the app and then re-added it, going through the whole setup process again.

In this video we'll be taking a look at 5 different errors the Litter-Robot 4 may run into and how to fix them. This include LED status identification of the...Just got my litter robot and I to am having this issue. It's just blinking red and green. Couldn't get the pairing yellow light to start blinking while holding the wifi button for 3 secs but the app let me continue and set up anyways. The robot is now listed in app and can be controlled via the app but the light is still flashing red and green.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. When I unplug the unit then plus it back in . Possible cause: FezFernando • 2 yr. ago. According to the quick start card, the rapidly flashin.