Did you know?

Litter-Robot 3: Filling the Globe. Fill the Globe through the opening with clumping litter until it meets the raised Fill Line when spread flat (about 8-10 pounds by weight or 1 gallon by volume). Be careful not to overfill the Globe. Then press the Reset button. Litter-Robot's litter sifting system requires clumping litter to work properly.Hi! I need your help with my Litter Robot 3. The yellow light on the unit is constantly on and my robot has stopped working. I did have the App but the App has deleted all my settings and will not reconnect. I have followed the advice for a hard reset, have taken it apart several times, cleaned sensors etc and it still doesn't work. If I disconnect the unit from the power and turn back on ...When you do a hard reset o factory reset the software of the Litter Robot 4 restarts to its original state, erasing the data, settings, and Apps connected to it. If you want to do a hard reset on your Litter Robot 4 you must do the following: Press and hold the Reset and Wifi buttons for three seconds. The panel's light will start a sequence ...r/litterrobot. •. BootleggerBill. Help! Rapidly flashing yellow cycle light. Our LR3 connect is displaying a rapidly flashing cycle light and will not work. I have completely dissembled and deep cleaned. I paid special attention tot he pinch detector and DFI areas, making sure that the pinch detector can move freely and the DFI sensor is clean.Install the new bonnet: Place the bonnet into the hinge behind the robot as shown. b. Rotate the bonnet downward over the globe and push down on the bonnet from the top to make sure it is latched and secure. (An audible "click" will be heard.) Press the Reset button to zero the weight sensors. Purchase Litter-Robot 4 Bonnet.My litter robot stops upside down during cycling. I have owned my Litter Robot 3 for a little over a year and about a week ago it began to get stuck upside down when cycling. The litter box becomes unusable, and the wastebin is exposed. The yellow light is blinking. In order to fix it, I've been having to turn the unit off and back on.Press the Cycle button to resume the cycle. Press the Reset button to abort the cycle and return the globe to the Home position. 3. After the litter is emptied, the globe pauses with the yellow light bar on and awaits your action. You may need to sweep any remaining litter toward the waste port. 4.Used your step by step directions and was able to replace motor and wire harness in my cats litter robot 2. When I connected the litter robot to power supply yellow soild light then red solid light motor would not turn. Thankfully, I had not put the top andd bottom together.Litter-Robot 3 Connect is a smart, self-cleaning litter box and comes with a 90-day in-home trial, comprehensive coverage with our WhiskerCare™ …Litter-Robot 4 can be equipped with (2) OdorTrap® Packs that are installed on the outer bottom area of the globe. The packs sit directly over the waste drawer to eliminate odors. ... Press the Cycle or Reset button to resume the clean cycle; when the clean cycle has ended, press the Reset button to zero the weight sensors. Purchase OdorTrap ...Since our review of the Litter-Robot III was published in July of 2020, we've gotten a lot of questions about this automatic litter box. In this video, you'l...The Litter-Robot 3 is equipped with Cat Sensor that detects when a cat enters and exits the globe. To ensure the accuracy and reliability of the Cat Sensor,...Whisker App Onboarding: Hard Reset. Press the Power button to turn the unit off. Unplug Litter-Robot from the rear of the base. Leave the unit off for 1 minute. Plug it back in. Press the Power button. Allow the unit to complete the initial Clean cycle. Try the onboarding process again.Looking for Litter-Robot 4? Click here. Didn't find what you're looking for? Phone and Chat support available Mon-Fri: 9AM-7PM EST and Sat: 9AM-5PM EST, or submit a ticket anytime. Chat with us 1-877-250-7729 Submit a ticket. Litter-Robot. Litter-Robot 4; Explore Litter-Robot 4; Litter-Robot 3 Connect; Accessories; Bundles;Litter-Robot 4 is the latest evolution of the highest-rated WiFi-enabled, automatic, self-cleaning litter box for cats. With over 20 years of customer feedback driving product innovation, Litter-Robot 4 features new sensor and litter-sifting technology for enhanced odour control, cat safety, and real-time tracking of waste and litter levels through the Whisker app.If your Whisker Litter-Robot 3 smart litter box is not working or not connecting, you can fix it by doing a hard factory reset to default settings.Get 80,000...Phone and Chat support available Mon-Fri: 9AM-7PMClean Cycle After your cat leaves the Globe, the Clean Cycle After your cat leaves the Globe, the Litter-Robot automatically performs a Clean cycle. The patented sifting system separates the clumps from the clean litter and deposits them into the Waste Drawer below. It takes about 2 minutes. You can also press the Cycle button to start a Clean cycle. Phone and Chat support available Mon-Fri: 9AM Reset the Unit: After clearing the jam, perform a manual reset of the Litter-Robot 4 to ensure that it is ready to resume automatic operation. Test Functionality: Once the jam has been cleared and the unit reset, test the Litter-Robot 4 to confirm that it is cycling properly and free from any remaining issues. So, let's talk a bit about what you should do when

Reset is under advanced options in the app. That's not an option for the LR4 anymore. Yes, it was changed recently. If you wait until the dfi has gone off to change the bag, the gauge will reset automatically, so you don't need to manually reset it in the app. Just tested this and it did not reset.Litter-Robot 4 is equipped with a flexible carbon filter pad that is installed on the outer bottom area of the globe. This filter sits directly over the waste drawer to absorb odors. ... Press the Cycle or Reset button to resume the clean cycle; when the clean cycle has ended, press the Reset button to zero the weight sensors.Here are the procedures you can do to fix the over-torque issue: 1. Reboot Your Litter-Robot. Sometimes, the Litter-Robot might just be acting up, so try rebooting the device. Empty the globe by removing the litter, then press the reset button on the robot.Hard reset: push and hold both the Connect and Reset Buttons at the same time until it turns off -> wait 2 minutes -> turn back on with power button. You can find the LR4 Troubleshooter which includes all other possible errors here. Edit 1: Added text steps. Edit 2: Added Link to LR4 Troubleshooter. Reply.

Cats should weigh at least 2.25kg before using the Litter-Robot in automatic mode. We recommend leaving the Litter-Robot off and operating in "semi-automatic" mode. When you see your cat has used the Litter-Robot, turn it on, and the Litter-Robot will automatically perform a clean cycle. Once it finishes (about 2 ½ minutes), turn the power ...How to change the Wait Time setting on Litter-Robot 3: Press and hold the Empty button on the Litter-Robot control panel for 3 seconds to enter Wait Time setting mode. One of the lights will start flashing, indicating the current Wait Time setting. Use the Reset button to toggle to the next setting: blue for 3 minutes, yellow for 7 minutes, and ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Get started by following the steps below. If possib. Possible cause: Don't forget to press the Reset button when you're done adding litter. 3. Replac.