Did you know?

Step Two: Locate the WPS button on the Xfinity router and press it for a few seconds. Step Three: Allow the Windows 11 PC and Xfinity Router to connect through WPS. On the WiFi network panel loaded in Step One, it should now read ‘Getting settings from the router’.A series of 3 short blinking green lights means your box is undergoing an update. Updates for Xfinity cable boxes are usually automatic. Expect to receive one periodically. For Xfinity X1 TV Boxes, they happen on a daily basis at a set hour. These updates help ensure that your cable box performs at the most optimal level.2. If the first step didn't resolve the issue, the next step is to reboot your Xfinity box by unplugging it for about 10-15 seconds, and then plugging it back in. Once it reboots, wait a few minutes until the white light stops blinking and returns to a steady state. 3. If the first two steps fail to resolve the issue, contact an Xfinity ...The remote works as a regular remote, so that part is fine. However the voice does not. I get a blue light and an odd noise like an "error". When I contact Comcast I get two different answers. At the store they gave me the remote, showed me where to plug into the IR port and how to pair. Online they said you need a DVR if you want to use voice ...As soon as you see that your remote is acting weird (blinking green and showing the battery icon on screen, like it just paired), go to your TV's pairing section in Settings > Remotes & Devices . Your TV will be in pairing mode as it searches for available devices. Press the pairing button on your remote (it's on the back) for about 5-7 seconds ...Hold the remote in such a way that its IR sensor faces the camera. Now press any button on the remote. If you see a bright red flashing light on your camera screen then your remote IR sensor is fine. If you don't see any flashing red light when you press the buttons on the remote then your remote sensor is defective.For blue blinking, replace batteries, ensure pairing, and check for loose buttons. Blinking lights on a remote are typically normal, as manufacturers include LEDs for illumination. Instead of wondering if a blinking remote is usual, assess if it indicates a problem. If your remote still functions despite blinking, it’s not an immediate concern.I've tried a system refresh, the xfinity assistant restarting it (can't connect to it), unplugging, checking cables, moving the box to another room - nothing is working. When I plug it in it will blink for a minute or two, I will get the welcome screen and then the blue light stops blinking and no light is visible. Help!Press and hold the Voice (Microphone) button while speaking a command into the microphone located at the top of your Voice Remote. Be sure to speak one to eight inches away from the microphone. Release the Voice (Microphone) button when you've finished the command. If you’re using an XRA Large Button Voice Remote, you can press and …Press and hold the A (triangle) and D (diamond) buttons at the same time for three seconds until the status light changes from red to green. Press 9-8-1. The LED will blink blue three times to indicate that the remote was reset. Then go to the on screen settings (the little gear) to the section that says "remote" and pair it again.The solid green light on the Comcast cable box is the signal we always want, and it simply indicates that the device is now ready to be used. In other words, it is time to turn on the cable. When the cable stops working or when there is a problem with the cable box, it can feel like life is put on hold.To turn Power Saver on: Navigate to Settings > Device Settings > Power Preferences > Power Saver > ON. Once your TV Box is powered down, turn it back on by pressing any button on your remote control. Note: New X1 TV Box installations will default to Power Saver "On." How much energy can be saved with Power Saver?Press the Setup button. Hold until the red LED at the top turns green. Press and hold the Xfinity button on the remote until the LED flashes green. You'll see on-screen pairing instructions. You might have to press it more than once in the case of XR2/XR5 remotes or if there is more than one set-top box within the range.Cable box blinking green, blue, and red. Hi, so my power went out last night for less than 5 minutes. When it came back on the cable box in my room started working properly and the wifi started working properly but the cable box in the living room is blinking green blue and red. I've tried holding down the power button for 10 seconds and ...That problem is this black screen issue is happening On your remote control, click on the Xfinity butto The following are the solutions that you can adopt to troubleshoot a blinking blue-and-white online light: 1. Power Cycle the Modem. The initial step is to perform a power cycle to address a modem that is not online and has a flashing blue and white light. Follow these steps to power cycle your Spectrum modem: Unplug the modem from the power ... Change the batteries: Take off the battery' Reboot your set-top box, if that doesn’t work. If holding your remote even an inch from your set-top box didn’t work, fret not. Rebooting may do the job. However, there are a few things you should note before you do this. … Usually flashing Yellow indicates no conn

Press the Setup button. Hold until the red LED at the top turns green. Press and hold the Xfinity button on the remote until the LED flashes green. You’ll see on-screen pairing instructions. You might have to press it more than once in the case of XR2/XR5 remotes or if there is more than one set-top box within the range.Change the batteries: Take off the battery’s compartment cover again. Remove the batteries. Insert new ones into your remote (ensure they’re properly aligned). Place your controller’s cover back. Note: All Xfinity remote models require 2 AA batteries. Now, check if your controller’s IR sensor finally works.Note: If your remote does not have an OK button, press the raised button in the center of the directional pad. Use the down arrow button to highlight Device Settings and press OK. Use the down arrow button to highlight Device Lights and press OK. Select Power Light Brightness and press OK. Use the left arrow or right arrow button to select the ...Aug 23, 2021 · The XiD-C cable box blue LED light is not on. This cable box was recently added and functions fine except for the blue LED. The Comcast tech brought it with him without the "new" packaging so I am assuming it is used. It is annoying not knowing whether the cable box has power or not without turning on the TV.Amazon customers can also recycle their old cameras by requesting a free UPS shipping label through the Amazon Recycling Progam. Amazon is now offering to replace customers’ discon...

Blink’s co-founders have been working in security and automation for a number of years, and they observed that there was a strong overlap between developer operations (DevOps) and ...Cable box has been refreshed, turned on and off but will only have a blinking blue light that stops after a minute. The screen only says welcome. @user_81c9f1 Hi there, thank you for taking the time to express your concerns inside the Xfinity Community Forum. You have reached the right place, and it would be my pleasure to help.My XR15 remote backlighting stopped working again. What can I do? ... or call Customer Service at 1-800-Comcast and have them send a remote to you, ...…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Solution: Clean the Remote Buttons. Remote buttons can beco. Possible cause: To turn off the blue light on your Xfinity cable box, there are a few steps you need .